Description/Application:

A precision die-cast expansion shield of rustproof alloy. Provides secure anchor-age of lag screws in mortar, stone and other types of solid masonry. Heavy external corrugations assure powerful gripping action. Long and short standard sizes for lag screws.Meets or Exceeds GSA specification FF-S-325 Group II Type 1 Class 1 & 2

Installation:

• Drill recommended hold size. Install shield flush or slightly below surface.
• Insert lag screw through fixture into shield and tighten

The post appeared first on shallcrossbolt.

*Each kit contains:
100 Plastic Anchors
100 Sheet Metal Screws
1 Masonry Drill Bit
Private label available on orders of 25 kits or more only
** Each kit contains:
50 Plastic Anchors
50 Sheet Metal Screws
1 Masonry Drill Bit
Private label available on orders of 25 kits or more only.
Plastic Anchor Kits…
NOW WITH YOUR
OWN PRIVATE LABEL!

Mix & Match Quantities

• Label may read however requested (e.g., address. Phone number, retail price). Maximum 4 lines. (29 characters/line max.)
• Available in Slotted Pan and Hex washer and Combination Head Screws.
• Must order a minimum combination of 25 kits.

Packed as Noted.
PLASTIC ANCHOR KIT
100-10-12 X 1” PLASTIC ANCHORS
100-10 X 1-1/4 SHEET METAL SCREWS
1-1/4” MASONARY DRILL
HOW TO INSTALL

1. DRILL ¼” HOLE APPROXIMATELY 1 ¼” DEEP WITH ENCHOLED DRILL
2. PLACE ANCHOR IN DRILLED HOLE AS FAR AS IT WILL GO.
3. INSERT SCREW THROUGH HOLE IN FIXTURE TO BE ANCHORED, THEN TURN SCREW TIGHT WITH ANCHOR.

BOLT’S HARDWARE 1243 NUT & WASHER ST. ANYTOWN, ANYWHERE 54321

A HARDWARE STORE AND MORE

The post appeared first on shallcrossbolt.

The post Acorn Nut, Hex Nut Carbon Steel Zinc Plated appeared first on shallcrossbolt.

Smaller Head Diameter
Description/Application:
The Sleeve anchor is the most versatile heavy-duty expansion anchor available. The sleeve expansion device allows this anchor to be used in cement, Block, thin wall or solid concrete, brick or stone. Ribbed sleeve design assures holding power of expansion sleeve. Hex nut styles provide a wide variety of industrial and commercial applications. Flat head variations are particularly useful for anchoring door and window frames. Comes complete with nuts an washers.

Installation:

• Drill hold to proper size to any depth exceeding minimum embedment. Outside diameter is necessarily larger than actual bolt diameter.
• Insert assembled anchor into hold, so that washer is flush with material to be fastened.
• Expand anchor by tightening nut or head 2 or 3 turns.

The post Acorn Nut, Hex Nut Stainless Steel appeared first on shallcrossbolt.

Meets or exceeds U.S.  Government G.S.A. Specifications FF-S-325 Group 11, Type 4, Class 1.
*Ultimate load capacity in 4000 PSI concrete. Laboratory test reports available upon request. Safe working loads for static loading should not exceed 25% of ultimate loads.

Description/Application:

The Wedge Anchor is easy to use. Anchor bolt, carbide bit, and hole size are all the same. Heavy-duty and versatile, the Wedge Anchor is non-bottom bearing, so precise hold depth or clean-out is not always required. A one-piece expanding clip assures full expansion for rugged, dependable holding strength. Available in zinc-plated carbon steel, galvanized steel and stainless steel.

(Comes Complete with washers and nuts.)

Note: Not recommended for use in lightweight masonry material such as block or brick. See next page for installation instruction

Additional Sizes & Bulk Quantities Available Upon Request.

The post Carbon Steel, Zinc Plated appeared first on shallcrossbolt.

Meets or exceeds U.S. Government G.S.A. Specifications FF-S-325 Group 11, Type 4, Class 1.
*Ultimate load capacity in 4000 PSI concrete. Laboratory test reports available upon request. Safe working loads for static loading should not exceed 25% of ultimate loads.
*Installation Instructions:

• Using a bit whose diameter equals the anchor diameter, drill hole to any depth exceeding minimum embedment. (D)
• Assemble anchor with nut and washer so that the top of the nuts is flush with the top of the anchor. Drive anchor through material to be fastened so that washer is flush with surface of material.
• Expand anchor by tightening nut 3 to 6 turns.

Additional Sizes & Bulk Quantities Available Upon Request.

The post Carbon Steel, Zinc Plated appeared first on shallcrossbolt.

Remember, anchor drills its own hold.
Note: Not recommended for use in lightweight masonry material such as block or brick.
Description/Application:

Accurate hold diameter and depth are assured with the Self-Drilling Anchor, because the anchor provides its own case hardened steel drill for every hole. This means a dependable, powerful holding capacity. Expands by driving anchor over the plug. Self-drilling anchors. Are especially useful for overhead application and where shock and vibration resistant anchoring is desired.
*Ultimate load capacity in 4713 PSI ¾ inch crushed limestone aggregate concrete. Capacities are for carbon steel versions only. Based on independent testing Laboratory tests. Safe working loads for single installations under static loading should not exceed 24% of the ultimate load capacity.

Installation:

1. Using anchor as the drill bit, drill hole until chuck holder is flush with surface of concrete. Remove anchor and clean out hold.
2. Insert plug in anchor. Expand anchor by reinserting it into hold and driving it in until chuch holder is flush with the surface of the concrete. Snap off cone.
3. Bolt the object to complete the installation.

This product to be discontinued-current inventory levels will not be replenished once depleted.
Please use caution when quoting. This product will not appear in the next issue of our catalog.

The post Chuck End Carbon Steel appeared first on shallcrossbolt.

*Note; Due to the softness of brass material, sillicon bronze lock washers should be used on brass bolts and screws when needed.

The post Countersunk Finish Brass appeared first on shallcrossbolt.

Description/Application:

A precision die-cast expansion shield of rustproof alloy. Provides secure anchor-age of lag screws in mortar, stone and other types of solid masonry. Heavy external corrugations assure powerful gripping action. Long and short standard sizes for lag screws.Meets or Exceeds GSA specification FF-S-325 Group II Type 1 Class 1 & 2

Installation:

• Drill recommended hold size. Install shield flush or slightly below surface.
• Insert lag screw through fixture into shield and tighten

The post Die Cast Expansion Shield Zinc Alloy appeared first on shallcrossbolt.

One setting tool include in each box.

Description/Application:

• A popular expansion anchor made up of a lead sleeve and threaded meal cone of rustproof alloy. Once being set in solid masonry, the lead sleeve expands into irregularities of hold. This allows the lead anchor to be used in many types of masonry including brick, block and stone. In making attachments to poor masonry, a deeper hole should be us

Installation:

1. Drill hole deeper inmasonry to a depth equal to the length of th anchor. Insert conical end first until flush with surface.
2. Use setting to expand lead sleeve into masonry with sharp hammer blows.
3. Install fixture by inserting an tightening a standard machine bolt or screw.

The post Expansion Anchor appeared first on shallcrossbolt.